楼主: pxjiangqi205

优酷路由宝刷磊科no1

[复制链接]

主题

好友

920

积分

中尉

该用户从未签到

发表于 2015-3-21 18:28 |显示全部楼层
Anywlan微信公众号

qos插件很牛,不会比nr235w、nr236差。
回复

使用道具 举报

主题

好友

920

积分

中尉

该用户从未签到

发表于 2015-3-21 18:40 |显示全部楼层
yaojbo8 发表于 2015-3-21 13:36
求刷回不死UBOOT.我还要刷OP。

现在磊科固件,我怎么刷不死UBOOT?

http://downloads.openwrt.org.cn/ ... ox-yk1-20150113.bin  这是下载地址啊。应该只能上ttl或编程器吧,好像telnet不行。
回复

使用道具 举报

主题

好友

37

积分

新兵上阵

该用户从未签到

发表于 2015-3-22 02:59 |显示全部楼层
pxjiangqi205 发表于 2015-3-21 18:40
http://downloads.openwrt.org.cn/PandoraBox/YouKu_YK1/u-boot/u-boot-pandorabox-yk1-20150113.bin  这 ...

TTL成功,但是无法中断,不能再继续下去了,怎么办?

U-Boot 1.1.3 (Nov 26 2013 - 15:10:32)

Board: Ralink APSoC DRAM:  128 MB
relocate_code Pointer at: 87fb0000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: ef 40 19 0 0 (40190000)
Warning: un-recognized chip ID, please update bootloader!
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 4.1.2.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 1024 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: SPI Flash
Date:Nov 26 2013  Time:15:10:32
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 580 MHZ ####
estimate memory size =128 Mbytes
rvlan initialization done
welcome!
   
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:50
   Image Name:   No1;;netcore
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    6779200 Bytes =  6.5 MB
   Load Address: 80000000
   Entry Point:  8000c310
raspi_read: from:50050 len:677140
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c310) ...
## Giving linux memsize in MB, 128

Starting kernel ...


LINUX started...

THIS IS ASIC
to 580 MHz

MIPS CPU sleep mode enabled.
PCIE: bypass PCIe DLL.
PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
disable all power about PCIe
CPU revision is: 00019650 (MIPS 24Kc)
Determined physical RAM map:
memory: 08000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00008000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00008000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00040208
Readback ErrCtl register=00040208
Memory: 124296k/131072k available (3621k kernel code, 6776k reserved, 994k data, 184k init, 0k highmem)
NR_IRQS:128
MTK/Ralink System Tick Counter init... cd:80467f18, m:214748, s:32
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocoPPLL_CFG1=0xe64000
MT7620 PPLL lock
PPLL_DRV =0x80080504
start PCIe register access
RALINK_PCI_PCICFG_ADDR = 1000f0

*************** MT7620 PCIe RC mode *************
PCIE0 no card, disable it(RST&CLK)
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource Ralink external timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RT3xxx EHCI/OHCI init.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (ZLIB) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
fuse init (API version 7.15)
msgmni has been set to 242
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
gpio_test_proc create proc success
Ralink gpio driver initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
brd: module loaded
loop: module loaded
deice id : ef 40 19 0 0 (40190000)
Warning: un-recognized chip ID, please update SPI driver!
W25Q128BV(ef 40180000) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (0M) .erasesize = 0x00000010 (0K) .numeraseregions = 65536
find key:hsqs from 0xbc050000 to 0xbc800000
offset:0x0000000000000000 size:0x0000000000000000 name:ALL
offset:0x0000000000000000 size:0x0000000000030000 name:Bootloader
offset:0xffffffffffffffff size:0x0000000000010000 namearameter2
offset:0xffffffffffffffff size:0x0000000000010000 name:Factory
offset:0xffffffffffffffff size:0x0000000000000000 name:Kernel
offset:0xffffffffffffffff size:0x00000000007b0000 name:RootFS
offset:0x0000000000050000 size:0x00000000007b0000 name:Kernel_RootFS
offset:0xffffffffffffffff size:0x0000000000060000 name:Kernel_mini
offset:0xffffffffffffffff size:0x0000000000050000 namearameter1
offset:0xffffffffffffffff size:0x0000000000800000 name:Application
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "arameter2"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x0000001e5190 : "Kernel"
mtd: partition "Kernel" doesn't end on an erase block -- force read-only
0x0000001e5190-0x000000750000 : "RootFS"
mtd: partition "RootFS" doesn't start on an erase block boundary -- force read-only
0x000000050000-0x000000750000 : "Kernel_RootFS"
0x000000750000-0x0000007b0000 : "Kernel_mini"
0x0000007b0000-0x000000800000 : "arameter1"
0x000000800000-0x000001000000 : "Application"
rdm_major = 253
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43762077
Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43762077
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
USB Serial support registered for cp210x
usbcore: registered new interface driver cp210x
cp210x: v0.09:Silicon Labs CP210x RS232 serial adaptor driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
MTK MSDC device init.
mtk-sd: MediaTek MT6575 MSDC Driver
hbwrr_reg:0
u32 classifier
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3000 buckets, 24000 max)
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux
net sniffer init ok.
TCP cubic registered
NET: Registered protocol family 17
L2TP core driver, V2.0
msdc0 -> ops_get_cd return<0> <- msdc_ops_get_cd() : L<2273> PID<kworker/u:1><0x1e>
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Registering the dns_resolver key type
NETCORE fastpath V0.03
VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
Freeing unused kernel memory: 184k freed

^C

init started:  BusyBox v1.1.2 (2014.06.18-09:03+0000) multi-call binary
Starting pid 39, console /dev/ttyS1: '/etc/rcS'
^C
Please press Enter to activate this console.
Starting pid 41, console /dev/ttyS1: '/bin/sh'


BusyBox v1.1.2 (2014.06.18-09:03+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

/ $
回复

使用道具 举报

主题

好友

37

积分

新兵上阵

该用户从未签到

发表于 2015-3-22 03:00 |显示全部楼层
pxjiangqi205 发表于 2015-3-21 18:25
目前可行办法是,拆开后盖刷通过ttl刷不死uboot,或者上编程器

通过ttl刷不死uboot,这个有具体操作吗?我TTL这时走不动了。
回复

使用道具 举报

主题

好友

920

积分

中尉

该用户从未签到

发表于 2015-3-22 14:16 |显示全部楼层
本帖最后由 pxjiangqi205 于 2015-3-22 14:50 编辑
yaojbo8 发表于 2015-3-22 02:59
TTL成功,但是无法中断,不能再继续下去了,怎么办?

U-Boot 1.1.3 (Nov 26 2013 - 15:10:32)

抱歉,刚才没有看启动日志,从日志上看好像是按回车键启动控制台。亲试一下吧,本人也是小白哦。晚上用ttl我也试一下,看有没有办法刷回去。磊科no1 启动中断要按住usb退出键,不过优酷路由没有这个按键。实在不行,就上编程器了。
回复

使用道具 举报

主题

好友

37

积分

新兵上阵

该用户从未签到

发表于 2015-3-22 14:19 |显示全部楼层
启动时按住ctrl +c不能中断吗?
不能中断。

磊科no1 启动中断要按住usb退出键,不过优酷路由没有这个按键。

看来得上编程器了,该买哪个?具体怎么弄?
回复

使用道具 举报

主题

好友

920

积分

中尉

该用户从未签到

发表于 2015-3-22 14:51 |显示全部楼层
本帖最后由 pxjiangqi205 于 2015-3-22 15:03 编辑
yaojbo8 发表于 2015-3-22 14:19
启动时按住ctrl +c不能中断吗?
不能中断。

从日志上看好像是按回车键启动控制台。不知道 这个控制台是什么东东,亲试一下吧,本人也是小白哦。晚上用ttl我也试一下,看有没有办法刷回去。
回复

使用道具 举报

主题

好友

2728

积分

少校

签到天数: 62 天

[LV.6]常住居民II

发表于 2015-3-23 20:39 |显示全部楼层
pxjiangqi205 发表于 2015-3-22 14:51
从日志上看好像是按回车键启动控制台。不知道 这个控制台是什么东东,亲试一下吧,本人也是小白哦。晚上 ...

不知道多拨插件可以用不?不然就换固件了
回复

使用道具 举报

主题

好友

777

积分

中尉

签到天数: 8 天

[LV.3]偶尔看看II

发表于 2015-3-24 01:22 |显示全部楼层
会出现问题吗?
回复

使用道具 举报

主题

好友

177

积分

上等兵

签到天数: 8 天

[LV.3]偶尔看看II

发表于 2015-3-24 09:01 |显示全部楼层
不知道有没有刷的,说说效果好不好。刷完以后还能刷回去吗?
回复

使用道具 举报

主题

好友

920

积分

中尉

该用户从未签到

发表于 2015-3-24 09:54 |显示全部楼层
AIRSHAPE 发表于 2015-3-23 20:39
不知道多拨插件可以用不?不然就换固件了

单线多拨在运营商没有做出限制的情况应该能用吧。这个主要得看运营商
回复

使用道具 举报

主题

好友

920

积分

中尉

该用户从未签到

发表于 2015-3-24 09:56 |显示全部楼层

目前没有问题,稳定运行两三天了。就是刷回去,只能上编程器了。mtd_write这个命令,没有运行权限,目前不上编程器刷不回去,正在想办法。
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 加入

本版积分规则

Archiver| 手机版| 中国无线门户 ( 粤ICP备11076993 ) |网站地图 

GMT+8, 2018-7-18 22:25

Powered by Discuz! X3.4

© 2003-2013 广州威思信息科技有限公司

返回顶部 返回列表