查看: 183|回复: 5

[求助] wr941n v6刷ddwrt变砖,u-boot tpl无法中断是什么情况??

[复制链接]

主题

好友

35

积分

新兵上阵

签到天数: 2 天

[LV.1]初来乍到

发表于 2016-9-22 06:17 |显示全部楼层
TG-NET
Anywlan微信公众号
刷的ddwrt目前最新版本,貌似09-14-2016的版本,从tp原厂升级,

结果变砖。。。。。。。

接ttl修复,结果uboot下等待一秒钟处按 tpl ,tp,TPL,##,123,ctrl+c,均无法中断启动。。。。。。。

目前无限重启中

*刷写软件各种都用过了,波特率也都试过了,tpl什么的就是没有反应,另外一个wr740n v4就可以tpl中断


请问,这个u-boot是本来就不可以中断还是有别的中断方法?

启动信息:


  1. U-Boot 1.1.4 (Mar 18 2013 - 19:23:53)

  2. U-boot DB120


  3. DRAM:  64 MB
  4. id read 0x100000ff
  5. flash size 4MB, sector count = 64
  6. Flash:  4 MB
  7. Using default environment

  8. PCIe Reset OK!!!!!!
  9. In:    serial
  10. Out:   serial
  11. Err:   serial
  12. Net:   ag934x_enet_initialize...
  13. No valid address in Flash. Using fixed address
  14. No valid address in Flash. Using fixed address
  15. wasp  reset mask:c03300
  16. WASP ----> S27 PHY
  17. : cfg1 0x5 cfg2 0x7114
  18. eth0: ba:be:fa:ce:08:41
  19. s27 reg init
  20. athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
  21. athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
  22. eth0 up
  23. WASP ----> S27 PHY
  24. : cfg1 0xf cfg2 0x7214
  25. eth1: ba:be:fa:ce:08:41
  26. s27 reg init lan
  27. ATHRS27: resetting s27
  28. ATHRS27: s27 reset done
  29. athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
  30. athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
  31. athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
  32. athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
  33. athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
  34. athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
  35. athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
  36. athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
  37. eth1 up
  38. eth0, eth1
  39. Autobooting in 1 seconds
  40. ## Booting image at 9f020000 ...
  41.    Uncompressing Kernel Image ... OK

  42. Starting kernel ...

  43. [    0.000000] Linux version 3.18.41 (root@nmndev) (gcc version 6.1.0 (LEDE GCC 6.1.0 r1259) ) #806 Wed Sep 14 03:53:42 CEST 2016
  44. [    0.000000] bootconsole [early0] enabled
  45. [    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
  46. [    0.000000] cpu srif ddr srif cpu 560 ddr 450 ahb 225
  47. AR9344
  48. detect mem size
  49. Uart Init
  50. Booting WASP !!! -:) ...
  51. [    0.000000] sys id = 2122 Atheros AR9344 ver 1 rev 1.2 (0x2122)
  52. [    0.000000] Determined physical RAM map:
  53. [    0.000000]  memory: 04000000 @ 00000000 (usable)
  54. [    0.000000] Zone ranges:
  55. [    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
  56. [    0.000000] Movable zone start for each node
  57. [    0.000000] Early memory node ranges
  58. [    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
  59. [    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
  60. [    0.000000] Primary instruction cache 64kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
  61. [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  62. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
  63. [    0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
  64. [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
  65. [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  66. [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  67. [    0.000000] Writing ErrCtl register=00000000
  68. [    0.000000] Readback ErrCtl register=00000000
  69. [    0.000000] Memory: 61484K/65536K available (2279K kernel code, 150K rwdata, 200K rodata, 176K init, 240K bss, 4052K reserved)
  70. [    0.000000] NR_IRQS:83
  71. [    0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
  72. [    0.070000] pid_max: default: 32768 minimum: 301
  73. [    0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  74. [    0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  75. [    0.080000] NET: Registered protocol family 16
  76. [    0.500000] Switched to clocksource MIPS
  77. [    0.510000] NET: Registered protocol family 2
  78. [    0.510000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  79. [    0.510000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  80. [    0.520000] TCP: Hash tables configured (established 1024 bind 1024)
  81. [    0.520000] TCP: reno registered
  82. [    0.530000] UDP hash table entries: 256 (order: 0, 4096 bytes)
  83. [    0.530000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  84. [    0.540000] NET: Registered protocol family 1
  85. [    0.540000] gpio_proc: module loaded and /proc/gpio/ created
  86. [    0.550000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
  87. [    0.560000] futex hash table entries: 256 (order: -1, 3072 bytes)
  88. [    0.570000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
  89. [    0.570000] msgmni has been set to 120
  90. [    0.580000] io scheduler noop registered (default)
  91. [    0.580000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
  92. 鶾    0.610000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
  93. [    0.620000] console [ttyS0] enabled
  94. [    0.620000] console [ttyS0] enabled
  95. [    0.630000] bootconsole [early0] disabled
  96. [    0.630000] bootconsole [early0] disabled
  97. [    0.640000] guessed flashsize = 4M
  98. [    0.640000] scanning for root partition
  99. [    0.640000] tplink uboot detected
  100. [    0.650000] guessed bootloader size = 20000
  101. [    0.660000]
  102. [    0.660000] found squashfs at 110000
  103. [    0.660000] adjusted length 3E0000, original length 3DC100
  104. [    0.670000] Creating 9 MTD partitions on "ar7240-nor0":
  105. [    0.680000] 0x000000000000-0x000000020000 : "RedBoot"
  106. [    0.680000] 0x000000020000-0x0000003e0000 : "linux"
  107. [    0.690000] 0x000000110000-0x0000003e0000 : "rootfs"
  108. [    0.690000] mtd: partition "rootfs" set to be root filesystem
  109. [    0.700000] 0x0000003e0000-0x000000400000 : "ddwrt"
  110. [    0.700000] 0x0000003e0000-0x0000003f0000 : "nvram"
  111. [    0.710000] 0x0000003f0000-0x000000400000 : "board_config"
  112. [    0.720000] 0x000000000000-0x000000400000 : "fullflash"
  113. [    0.720000] 0x000000000000-0x000000020000 : "fullboot"
  114. [    0.730000] 0x000000010000-0x000000020000 : "uboot-env"
  115. [    0.730000] libphy: Fixed MDIO Bus: probed
  116. [    0.740000] tun: Universal TUN/TAP device driver, 1.6
  117. [    0.740000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  118. [    0.750000] PPP generic driver version 2.4.2
  119. [    0.750000] PPP BSD Compression module registered
  120. [    0.760000] PPP Deflate Compression module registered
  121. [    0.760000] PPP MPPE Compression module registered
  122. [    0.770000] NET: Registered protocol family 24
  123. [    0.780000] u32 classifier
  124. [    0.780000]     Performance counters on
  125. [    0.790000]     input device check on
  126. [    0.790000]     Actions configured
  127. [    0.790000] Netfilter messages via NETLINK v0.30.
  128. [    0.800000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
  129. [    0.810000] nf_conntrack_rtsp v0.7 loading
  130. [    0.810000] nf_nat_rtsp v0.7 loading
  131. [    0.810000] ip_tables: (C) 2000-2006 Netfilter Core Team
  132. [    0.820000] TCP: westwood registered
  133. [    0.820000] TCP: hybla registered
  134. [    0.830000] TCP: vegas registered
  135. [    0.830000] NET: Registered protocol family 17
  136. [    0.830000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
  137. [    0.850000] Bridge firewalling registered
  138. [    0.850000] 8021q: 802.1Q VLAN Support v1.8
  139. [    0.870000] searching for nvram
  140. [    0.870000] nvram size = 0
  141. [    0.900000] Atheros AR71xx hardware watchdog driver version 0.1.0
  142. [    0.910000] ar71xx-wdt: timeout=15 secs (max=107) ref freq=40000000
  143. [    0.920000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  144. [    0.930000] Freeing unused kernel memory: 176K (802f4000 - 80320000)
  145. start service
  146. starting Architecture code for dir615e
  147. udevtrigger[256]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory
  148. load ATH Ethernet Driver
  149. [    3.230000] libphy: ag71xx_mdio: probed
  150. [    3.820000] ag71xx ag71xx.1: invalid speed specified
  151. [    3.820000] ag71xx: probe of ag71xx.1 failed with error -22
  152. [    4.420000] ag71xx ag71xx.0: invalid speed specified
  153. [    4.420000] ag71xx: probe of ag71xx.0 failed with error -22
  154. Failed to connect to the switch. Use the "list" command to see which switches are available.
  155. Failed to connect to the switch. Use the "list" command to see which switches are available.
  156. Failed to connect to the switch. Use the "list" command to see which switches are available.
  157. Failed to connect to the switch. Use the "list" command to see which switches are available.
  158. sh: can't create /sys/class/leds/generic_7/port_mask: Permission denied
  159. sh: can't create /sys/class/leds/generic_6/port_mask: Permission denied
  160. sh: can't create /sys/class/leds/generic_5/port_mask: Permission denied
  161. sh: can't create /sys/class/leds/generic_4/port_mask: Permission denied
  162. load ATH 802.11 a/b/g Driver
  163. load ATH9K 802.11n Driver
  164. [    4.640000] Loading modules backported from Linux version wt-2016-06-20-0-gbc17424
  165. [    4.640000] Backport generated by backports.git backports-20160216-7-g5735958
  166. [    5.360000] ath: phy0: Unable to initialize hardware; initialization status: -5
  167. [    5.370000] ath9k ar934x_wmac: failed to initialize device
  168. [    5.380000] ath9k: probe of ar934x_wmac failed with error -5
  169. [    8.480000] device br0 entered promiscuous mode
  170. [    8.500000] device br0 left promiscuous mode
  171. [    8.510000] device br0 entered promiscuous mode
  172. [    8.530000] device br0 left promiscuous mode
  173. [    8.980000] random: dnsmasq urandom read with 16 bits of entropy available
  174. /opt/etc/init.d/rcS: No such file or directory
  175. /jffs/etc/init.d/rcS: No such file or directory
  176. /mmc/etc/init.d/rcS: No such file or directory
  177. /etc/config/conntrack.startup: line 8: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
  178. resetbutton: factory default.
  179. send dhcp lease release signal
  180. Sending SIGTERM [   15.820000] ar71xx-wdt: device closed unexpectedly, watchdog timer will not stop!
  181. to all processes
  182. unmounting /
  183. unmounting /
  184. Sending SIGKILL to all processes
  185. unmounting /
  186. unmounting /
  187. [   23.880000] reboot: Restarting system
复制代码

就这些信息无限循环

主题

好友

171

积分

上等兵

签到天数: 3 天

[LV.2]偶尔看看I

发表于 2016-9-22 07:12 |显示全部楼层
Autobooting in 1 seconds 后按那3个键盘速度一定要快,1秒内 多试几次就成功了......
回复

使用道具 举报

主题

好友

3891

积分

少校

签到天数: 388 天

[LV.9]以坛为家II

发表于 2016-9-22 08:59 |显示全部楼层
风枪吹下来编程器刷吧。
回复

使用道具 举报

主题

好友

7470

积分

中校

签到天数: 331 天

[LV.8]以坛为家I

发表于 2016-9-22 10:40 |显示全部楼层
是固件问题,941ND V6是国外版,国内版941N V6CPU不同,造成很多路由器变砖。懂英文的应该向DD官网反映投诉。
回复

使用道具 举报

主题

好友

35

积分

新兵上阵

签到天数: 2 天

[LV.1]初来乍到

发表于 2016-9-23 05:32 |显示全部楼层
jie613 发表于 2016-9-22 10:40
是固件问题,941ND V6是国外版,国内版941N V6CPU不同,造成很多路由器变砖。懂英文的应该向DD官网反映投诉 ...

也就是说国内v6不能刷dd咯?

cpu是ar9344难道国外版不是这个cpu??
回复

使用道具 举报

主题

好友

35

积分

新兵上阵

签到天数: 2 天

[LV.1]初来乍到

发表于 2016-9-23 05:34 |显示全部楼层
13062678135 发表于 2016-9-22 08:59
风枪吹下来编程器刷吧。

看来是只能拆下来写了。。。。。。。。。。

找知道先刷openwrt再把不死刷了,最后慢慢来搞其他固件。。。。。。。。
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 我要加入

本版积分规则

Archiver| 手机版| 中国无线门户 ( 粤ICP备11076993 )  |网站地图    小黑屋 | 免责声明

GMT+8, 2016-12-3 21:46

Powered by Discuz! X3.2

© 2003-2013 广州威思信息科技有限公司

返回顶部 返回列表