查看: 289|回复: 10

[求助] tplink wr941nv6刷openwrt后,设置错误,连不上了!求助

[复制链接]

主题

好友

39

积分

新兵上阵

签到天数: 3 天

[LV.2]偶尔看看I

发表于 2017-4-20 10:50 |显示全部楼层
Anywlan微信公众号
我的wr941nv6红黑版的,刷了openwrt,刚刷完后可以用的,后来设置局域网一些参数时,保存并应用,发现网络不通了。想重新登陆192.168.1.1设置路由,发现进不去了。ping不通,路由加电过程中ping 192.168.1.1 t, 只有1行或2行通,telnet当然也不通的,拆机,上ttl,中断不了。信息如下:
U-Boot 1.1.4 (Mar 18 2013 - 19:23:53)

U-boot DB120


DRAM:  64 MB
id read 0x100000ff
flash size 4MB, sector count = 64
Flash:  4 MB
Using default environment

PCIe Reset OK!!!!!!
In:    serial
Out:   serial
Err:   serial
Net:   ag934x_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
wasp  reset mask:c03300
WASP ----> S27 PHY
: cfg1 0x5 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
WASP ----> S27 PHY
: cfg1 0xf cfg2 0x7214
eth1: ba:be:fa:ce:08:41
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.18.23 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro

GCC 4.8-2014.04 r47269) ) #1 Sun Jan 31 18:39:35 CET 2016
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9344 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WDR3500  console=ttyS0,115200

rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 60812K/65536K available (2586K kernel code, 128K rwdata, 540K

rodata, 256K init, 193K bss, 4724K reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
[    0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090000] NET: Registered protocol family 16
[    0.090000] MIPS: machine is TP-LINK TL-WDR3500
[    0.100000] registering PCI controller with io_map_base unset
[    0.550000] PCI host bridge to bus 0000:00
[    0.550000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.560000] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.560000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.570000] pci 0000:00:00.0: invalid calibration data
[    0.570000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[    0.580000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[    0.580000] pci 0000:00:00.0: using irq 40 for pin 1
[    0.590000] Switched to clocksource MIPS
[    0.590000] NET: Registered protocol family 2
[    0.600000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.600000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.610000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.610000] TCP: reno registered
[    0.620000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.620000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.630000] NET: Registered protocol family 1
[    0.630000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.660000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.670000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c)

2001-2006 Red Hat, Inc.
[    0.680000] msgmni has been set to 118
[    0.680000] io scheduler noop registered
[    0.680000] io scheduler deadline registered (default)
[    0.690000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
鶾    0.720000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a

16550A
[    0.730000] console [ttyS0] enabled
[    0.730000] console [ttyS0] enabled
[    0.740000] bootconsole [early0] disabled
[    0.740000] bootconsole [early0] disabled
[    0.750000] m25p80 spi0.0: found s25sl032p, expected m25p80
[    0.750000] m25p80 spi0.0: s25sl032p (4096 Kbytes)
[    0.760000] 5 tp-link partitions found on MTD device spi0.0
[    0.760000] Creating 5 MTD partitions on "spi0.0":
[    0.770000] 0x000000000000-0x000000020000 : "u-boot"
[    0.770000] 0x000000020000-0x00000013f634 : "kernel"
[    0.780000] 0x00000013f634-0x0000003f0000 : "rootfs"
[    0.790000] mtd: device 2 (rootfs) set to be root filesystem
[    0.790000] 1 squashfs-split partitions found on MTD device rootfs
[    0.800000] 0x000000360000-0x0000003f0000 : "rootfs_data"
[    0.810000] 0x0000003f0000-0x000000400000 : "art"
[    0.810000] 0x000000020000-0x0000003f0000 : "firmware"
[    0.840000] libphy: ag71xx_mdio: probed
[    1.430000] ag71xx-mdio.1: Found an AR934X built-in switch
[    1.470000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    2.070000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042,

driver=Generic PHY]
[    2.080000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    2.080000] TCP: cubic registered
[    2.090000] NET: Registered protocol family 17
[    2.090000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update

your scripts to load br_netfilter if you need this.
[    2.110000] Bridge firewalling registered
[    2.110000] 8021q: 802.1Q VLAN Support v1.8
[    2.120000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.130000] Freeing unused kernel memory: 256K (80390000 - 803d0000)
[    3.170000] init: Console is alive
[    3.180000] init: - watchdog -
[    5.180000] init: - preinit -
[    5.790000] random: procd urandom read with 9 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.050000] jffs2: notice: (346) jffs2_build_xattr_subsystem: complete building xattr

subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    9.060000] mount_root: switching to jffs2 overlay
[    9.120000] procd: - early -
[    9.120000] procd: - watchdog -
[    9.860000] procd: - ubus -
[   10.880000] procd: - init -
Please press Enter to activate this console.
[   11.720000] NET: Registered protocol family 10
[   11.740000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   11.750000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[   11.760000] Backport generated by backports.git backports-20150129-0-gdd4a670
[   11.770000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.790000] nf_conntrack version 0.5.0 (954 buckets, 3816 max)
[   11.830000] xt_time: kernel timezone is -0000
[   11.860000] cfg80211: Calling CRDA to update world regulatory domain
[   11.890000] cfg80211: World regulatory domain updated:
[   11.890000] cfg80211:  DFS Master region: unset
[   11.900000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain,

max_eirp), (dfs_cac_time)
[   11.910000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   11.910000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A,

2000 mBm), (N/A)
[   11.920000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   11.930000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A,

2000 mBm), (N/A)
[   11.940000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A,

2000 mBm), (0 s)
[   11.950000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   11.960000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   11.970000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   12.030000] PPP generic driver version 2.4.2
[   12.030000] NET: Registered protocol family 24
[   12.100000] ath: phy0: Unable to initialize hardware; initialization status: -5
[   12.100000] ath9k ar934x_wmac: failed to initialize device
[   12.110000] ath9k: probe of ar934x_wmac failed with error -5
[   12.120000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   12.140000] ieee80211 phy1: Atheros AR9300 Rev:3 mem=0xb0000000, irq=40
[   12.150000] cfg80211: Calling CRDA for country: US
[   12.150000] cfg80211: Regulatory domain changed to country: US
[   12.160000] cfg80211:  DFS Master region: FCC
[   12.160000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain,

max_eirp), (dfs_cac_time)
[   12.170000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[   12.180000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A,

2300 mBm), (N/A)
[   12.190000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A,

2300 mBm), (0 s)
[   12.200000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2300 mBm), (0 s)
[   12.210000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[   12.220000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm),

(N/A)
[   20.800000] device eth1 entered promiscuous mode
[   20.830000] br-wan: port 1(eth1) entered forwarding state
[   20.830000] br-wan: port 1(eth1) entered forwarding state
[   20.870000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   21.800000] br-wan: port 1(eth1) entered disabled state
[   22.000000] cfg80211: Calling CRDA for country: CN
[   22.000000] cfg80211: Regulatory domain changed to country: CN
[   22.010000] cfg80211:  DFS Master region: FCC
[   22.010000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain,

max_eirp), (dfs_cac_time)
[   22.020000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   22.030000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A,

2300 mBm), (N/A)
[   22.040000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A,

2300 mBm), (0 s)
[   22.050000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[   22.060000] cfg80211:   (57240000 KHz - 59400000 KHz @ 2160000 KHz), (N/A, 2800 mBm),

(N/A)
[   22.060000] cfg80211:   (59400000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4400 mBm),

(N/A)
[   22.070000] cfg80211:   (63720000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 2800 mBm),

(N/A)
[   23.290000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready

求大神帮忙分析一下什么问题,怎么解决,上编程器需要拆芯片吗,另外该用openwrt的固件,还是用原厂的固件,mac地址怎么处理呀

主题

好友

6136

积分

中校

签到天数: 446 天

[LV.9]以坛为家II

发表于 2017-4-20 13:17 |显示全部楼层
进uboot重刷个固件试试
回复

使用道具 举报

主题

好友

231

积分

少尉

签到天数: 11 天

[LV.3]偶尔看看II

发表于 2017-4-20 19:37 |显示全部楼层
这个固件是很不错

回复

使用道具 举报

主题

好友

326

积分

少尉

签到天数: 10 天

[LV.3]偶尔看看II

发表于 2017-4-26 11:14 |显示全部楼层
MAC地址在bread里面改。
回复

使用道具 举报

主题

好友

1715

积分

上尉

签到天数: 65 天

[LV.6]常住居民II

发表于 2017-4-26 12:12 手机上Anywlan 随时随地无线:http://m.Anywlan.com |显示全部楼层
固件分享一下,我也试试
回复

使用道具 举报

主题

好友

165

积分

上等兵

签到天数: 2 天

[LV.1]初来乍到

发表于 2017-4-26 16:05 手机上Anywlan 随时随地无线:http://m.Anywlan.com |显示全部楼层
我的也是wr941nv6刷openwrt的  我设置了网口桥接无线  当无线网卡用 设置好就可以用了 不过我重启后就不行了 也是进不了设置页面 !
回复

使用道具 举报

主题

好友

165

积分

上等兵

签到天数: 2 天

[LV.1]初来乍到

发表于 2017-4-26 16:07 手机上Anywlan 随时随地无线:http://m.Anywlan.com |显示全部楼层
能进安全模式 能p通 但到telnet那一步就不行了
回复

使用道具 举报

主题

好友

165

积分

上等兵

签到天数: 2 天

[LV.1]初来乍到

发表于 2017-4-26 21:34 手机上Anywlan 随时随地无线:http://m.Anywlan.com |显示全部楼层
那位老哥教教我怎么搞?

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有帐号?我要加入

x
回复

使用道具 举报

主题

好友

165

积分

上等兵

签到天数: 2 天

[LV.1]初来乍到

发表于 2017-4-27 18:10 手机上Anywlan 随时随地无线:http://m.Anywlan.com |显示全部楼层
回复

使用道具 举报

主题

好友

165

积分

上等兵

签到天数: 2 天

[LV.1]初来乍到

发表于 2017-4-27 19:21 |显示全部楼层
那位大哥会搞啊?

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有帐号?我要加入

x
回复

使用道具 举报

主题

好友

165

积分

上等兵

签到天数: 2 天

[LV.1]初来乍到

发表于 2017-4-27 22:26 |显示全部楼层
网上找教程搞定了!

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有帐号?我要加入

x
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 我要加入

本版积分规则

Archiver| 手机版| 中国无线门户 ( 粤ICP备11076993 )  |网站地图    小黑屋 | 免责声明

GMT+8, 2017-7-21 00:39

Powered by Discuz! X3.2

© 2003-2013 广州威思信息科技有限公司

返回顶部 返回列表