查看: 353|回复: 13

[求助] OPENWRT无法进LUCI配置,ping不通,TLL信息如何解读

[复制链接]

主题

好友

334

积分

少尉

签到天数: 1 天

[LV.1]初来乍到

发表于 2017-7-12 12:26 |显示全部楼层
Anywlan微信公众号
本帖最后由 joehunter 于 2017-7-12 12:33 编辑

此贴接上面二帖, OPENWRT无法进入配置界面  OP无法登陆web界面、无法telnet
实在没办法,买了根TLL线,信息如下,请大家帮忙解读一下是什么原因。这个应该可以在SecureCRT下清空配置后恢复初始吧???--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------分割线

U-Boot 1.1.4 (Apr  7 2011 - 18:59:04)

AP81 (ar7100) U-boot by dyq
DRAM:  
sri
64 MB
id read 0x100000ff
flash size 8MB, sector count = 256
Flash: 16 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:  ag7100_enet_initialize...
Fetching MAC Address from 0x83fef2f0
eth0: 00:03:7f:e0:05:ea
eth0 up
eth0
Autobooting in 1 seconds, press t to stop## Booting image atbf020000 ...
   Uncompressing Kernel Image... OK

Starting kernel ...



OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Looking for OpenWrt image... found at 0xbf022000
Decompressing kernel... done!
Starting kernel at 80060000...

[    0.000000] Linux version3.3.8 (haxc@PC) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02)) #15 Mon Nov 4 23:43:00 CST 2013
[    0.000000] bootconsole[early0] enabled
[    0.000000] CPU revisionis: 00019374 (MIPS 24Kc)
[    0.000000] SoC: AtherosAR9130 rev 2
[    0.000000] Clocks:CPU:400.000MHz, DDR:400.000MHz, AHB:100.000MHz, Ref:5.000MHz
[    0.000000] Determinedphysical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFNranges:
[    0.000000]   Normal  0x00000000 -> 0x00004000
[    0.000000] Movable zonestart PFN for each node
[    0.000000] Early memoryPFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1zonelists in Zone order, mobility grouping on. Total pages: 16256
[    0.000000] Kernel commandline:  board=TL-WR941NDconsole=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash tableentries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cachehash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cachehash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primaryinstruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary datacache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtlregister=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory:61516k/65536k available (2191k kernel code, 4020k reserved, 411k data, 212kinit, 0k highmem)
[    0.000000] SLUB:Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibratingdelay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max:default: 32768 minimum: 301
[    0.080000] Mount-cachehash table entries: 512
[    0.090000] NET: Registeredprotocol family 16
[    0.090000] gpiochip_add:registered GPIOs 0 to 21 on device: ath79
[    0.100000] MIPS: machineis TP-LINK TL-WR941ND
[    0.360000] bio: createslab <bio-0> at 0
[    0.370000] Switching toclocksource MIPS
[    0.380000] NET: Registeredprotocol family 2
[    0.380000] IP route cachehash table entries: 1024 (order: 0, 4096 bytes)
[    0.380000] TCP establishedhash table entries: 2048 (order: 2, 16384 bytes)
[    0.390000] TCP bind hashtable entries: 2048 (order: 1, 8192 bytes)
[    0.390000] TCP: Hashtables configured (established 2048 bind 2048)
[    0.400000] TCP renoregistered
[    0.400000] UDP hash tableentries: 256 (order: 0, 4096 bytes)
[    0.410000] UDP-Lite hashtable entries: 256 (order: 0, 4096 bytes)
[    0.420000] NET: Registeredprotocol family 1
[    0.440000] squashfs:version 4.0 (2009/01/31) Phillip Lougher
[    0.440000] JFFS2 version2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat,Inc.
[    0.450000] msgmni has beenset to 120
[    0.460000] io schedulernoop registered
[    0.460000] io schedulerdeadline registered (default)
[    0.470000] Serial:8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.490000] serial8250.0:ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.500000] console [ttyS0]enabled, bootconsole disabled
[    0.500000] console [ttyS0]enabled, bootconsole disabled
[    0.520000] m25p80 spi0.0:found mx25l12805d, expected m25p80
[    0.520000] m25p80 spi0.0:mx25l12805d (16384 Kbytes)
[    0.530000] 6 tp-linkpartitions found on MTD device spi0.0
[    0.530000] Creating 6 MTDpartitions on "spi0.0":
[    0.540000]0x000000000000-0x000000020000 : "u-boot"
[    0.540000]0x000000020000-0x00000010a800 : "kernel"
[    0.550000] mtd: partition"kernel" must either start or end on erase block boundary or besmaller than an erase block -- forcing read-only
[    0.560000]0x00000010a800-0x000000ff0000 : "rootfs"
[    0.570000] mtd: partition"rootfs" must either start or end on erase block boundary or besmaller than an erase block -- forcing read-only
[    0.580000] mtd: partition"rootfs" set to be root filesystem
[    0.590000] mtd: partition"rootfs_data" created automatically, ofs=E40000, len=1B0000
[    0.600000]0x000000e40000-0x000000ff0000 : "rootfs_data"
[    0.600000]0x000000ff0000-0x000001000000 : "art"
[    0.610000]0x000000020000-0x000000ff0000 : "firmware"
[    0.620000]0x000000000000-0x000001000000 : "fullflash"
[    0.630000]  Hooked IMQ after mangle on PREROUTING
[    0.630000]  Hooked IMQ after nat on POSTROUTING
[    0.630000] IMQ driverloaded successfully. (numdevs = 2, numqueues = 1)
[    0.660000] ag71xx_mdio:probed
[    0.660000] eth0: AtherosAG71xx at 0xb9000000, irq 4
[    0.970000] TCP cubicregistered
[    0.970000] NET: Registeredprotocol family 17
[    0.970000] DistributedSwitch Architecture driver version 0.1
[    0.980000] eth0[0]:detected a Marvell 88E6060 switch
[    1.010000] dsa slave smi:probed
[    1.020000] 8021q: 802.1QVLAN Support v1.8
[    1.030000] VFS: Mountedroot (squashfs filesystem) readonly on device 31:2.
[    1.040000] Freeing unusedkernel memory: 212k freed
[    4.090000] eth0: link up(100Mbps/Full duplex)
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    7.700000] JFFS2 notice511) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 ofxdatum (1 unchecked, 0 orphan) and 49 of xref (0 dead, 6 orphan) found.
[    8.680000] SCSI subsysteminitialized
[    8.950000] usbcore:registered new interface driver usbfs
[    8.960000] usbcore:registered new interface driver hub
[    8.960000] usbcore:registered new device driver usb
[    9.710000] ehci_hcd: USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    9.720000] ehci-platformehci-platform: Generic Platform EHCI Controller
[    9.730000] ehci-platformehci-platform: new USB bus registered, assigned bus number 1
[    9.770000] ehci-platformehci-platform: irq 3, io mem 0x1b000000
[    9.790000] ehci-platformehci-platform: USB 2.0 started, EHCI 1.00
[    9.790000] hub 1-0:1.0:USB hub found
[    9.800000] hub 1-0:1.0: 1port detected
[    9.900000] ohci_hcd: USB1.1 'Open' Host Controller (OHCI) Driver
[    9.970000] InitializingUSB Mass Storage driver...
[    9.970000] usbcore:registered new interface driver usb-storage
[    9.980000] USB MassStorage support registered.
switching to jffs2
- init -
[   31.910000] eth0: link down

Please press Enter to activate this console. [   35.090000] Loading modules backported fromLinux version master-2013-06-27-0-gdcfa6d5
[   35.100000] Backportgenerated by backports.git backports-20130617-4-ge3220f5
[   35.310000] cfg80211:Calling CRDA to update world regulatory domain
[   35.320000] cfg80211: Worldregulatory domain updated:
[   35.320000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain,max_eirp)
[   35.330000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz),(300 mBi, 2000 mBm)
[   35.340000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz),(300 mBi, 2000 mBm)
[   35.340000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz),(300 mBi, 2000 mBm)
[   35.350000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz),(300 mBi, 2000 mBm)
[   35.360000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz),(300 mBi, 2000 mBm)
[   35.730000] NET: Registeredprotocol family 10
[   37.540000] usbcore:registered new interface driver rt73usb
[   37.600000] usbcore:registered new interface driver rtl8187
[   37.660000] ieee80211 phy0:Atheros AR9100 MAC/BB Rev:7 AR2122 RF Rev:a2 mem=0xb80c0000, irq=2
[   37.670000] cfg80211:Calling CRDA for country: US
[   37.670000] cfg80211:Regulatory domain changed to country: US
[   37.680000] cfg80211:   (start_freq - end_freq @ bandwidth),(max_antenna_gain, max_eirp)
[   37.690000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz),(300 mBi, 2700 mBm)
[   37.700000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz),(300 mBi, 1700 mBm)
[   37.700000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz),(300 mBi, 2000 mBm)
[   37.710000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz),(300 mBi, 2000 mBm)
[   37.720000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz),(300 mBi, 2000 mBm)
[   37.730000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz),(300 mBi, 3000 mBm)
[   37.770000] usbcore:registered new interface driver rt2800usb
[   38.430000] RPC: Registerednamed UNIX socket transport module.
[   38.430000] RPC: Registeredudp transport module.
[   38.440000] RPC: Registeredtcp transport module.
[   38.440000] RPC: Registeredtcp NFSv4.1 backchannel transport module.
[   39.250000] PPP genericdriver version 2.4.2
[   40.000000] tun: UniversalTUN/TAP device driver, 1.6
[   40.010000] tun: (C)1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   40.170000] PPP MPPECompression module registered
[   40.300000] usbcore:registered new interface driver p54usb
[   40.570000] L2TP coredriver, V2.0
[   40.590000] L2TP netlinkinterface
[   40.710000] IPv6 over IPv4tunneling driver
[   40.970000] GRE over IPv4demultiplexor driver
[   41.070000] GRE over IPv4tunneling driver
[   41.370000] Installingknfsd (copyright (C) 1996 [url=mailtokir@monad.swb.de]okir@monad.swb.de[/url]).
[   41.770000] ip_tables: (C)2000-2006 Netfilter Core Team
[   42.270000] NET: Registeredprotocol family 24
[   42.500000] nf_conntrackversion 0.5.0 (964 buckets, 3856 max)
[   43.080000] PPPoL2TP kernel driver, V2.0
[   43.110000] PPTP driverversion 0.8.5
[   44.210000] xt_time: kerneltimezone is -0000
[   45.640000] xt_length2:Unknown symbol ipv6_find_hdr (err 0)
[   45.800000] xt_RAWNAT:Unknown symbol ipv6_find_hdr (err 0)
[   45.860000] xt_SYSRQ:Unknown symbol ipv6_find_hdr (err 0)
[   45.940000] Netfiltermessages via NETLINK v0.30.
[   46.130000] ip6_tables: (C)2000-2006 Netfilter Core Team
[   46.550000] ip_set:protocol 6
[   47.160000] NF_TPROXY:Transparent proxy support initialized, version 4.1.0
[   47.170000] NF_TPROXY:Copyright (c) 2006-2007 BalaBit IT Ltd.
[   47.710000] i2c /deventries driver
[   47.840000] usbcore:registered new interface driver ath9k_htc
[   48.160000] usbcore:registered new interface driver snd-usb-audio
[   48.300000] usbcore:registered new interface driver usblp
[   48.340000] usbcore:registered new interface driver usbserial
[   48.350000] USB Serialsupport registered for generic
[   48.350000] usbcore:registered new interface driver usbserial_generic
[   48.360000] usbserial: USBSerial Driver core
[   48.540000] usbcore:registered new interface driver ums-alauda
[   48.570000] usbcore:registered new interface driver ums-cypress
[   48.650000] usbcore:registered new interface driver ums-datafab
[   48.680000] usbcore:registered new interface driver ums-freecom
[   48.720000] usbcore:registered new interface driver ums-isd200
[   48.750000] usbcore:registered new interface driver ums-jumpshot
[   48.790000] usbcore:registered new interface driver ums-karma
[   48.820000] usbcore:registered new interface driver ums-sddr09
[   48.860000] usbcore:registered new interface driver ums-sddr55
[   48.890000] usbcore:registered new interface driver ums-usbat
[   49.050000] Linux videocapture interface: v2.00
[   49.200000] usbcore:registered new interface driver zd1211rw
[   49.610000] USB Serialsupport registered for ch341-uart
[   49.610000] usbcore:registered new interface driver ch341
[   49.740000] USB Serialsupport registered for FTDI USB Serial Device
[   49.750000] usbcore:registered new interface driver ftdi_sio
[   49.760000] ftdi_sio:v1.6.0:USB FTDI Serial Converters Driver
[   49.880000] USB Serialsupport registered for pl2303
[   49.890000] usbcore:registered new interface driver pl2303
[   49.890000] pl2303rolific PL2303 USB to serial adaptor driver
[   50.220000] usbcore:registered new interface driver usbhid
[   50.220000] usbhid: USB HIDcore driver
[   50.350000] cpia2:V4L-Driver for Vision CPiA2 based cameras v3.0.1
[   50.360000] usbcore:registered new interface driver cpia2
[   50.490000] gspca_main:v2.14.0 registered
[   50.610000] usbcore:registered new interface driver Philips webcam
[   50.650000] fuse init (APIversion 7.18)
[   50.970000] usbcore:registered new interface driver uvcvideo
[   50.980000] USB Video Classdriver (1.1.1)
[   61.460000] ar71xx: pll_reg0xb8050014: 0x13000a44
[   61.470000] eth0: link up(100Mbps/Full duplex)
[  61.500000] device eth0 entered promiscuous mode
[   61.500000] br-eth: port1(eth0) entered forwarding state
[   61.510000] br-eth: port1(eth0) entered forwarding state
[  61.530000] ADDRCONF(NETDEV_UP): lan1: link is not ready
[   61.570000] device lan1entered promiscuous mode
[  61.570000] ADDRCONF(NETDEV_UP): br-lan: link is not ready
[  61.580000] ADDRCONF(NETDEV_UP): lan2: link is not ready
[  61.650000] device lan2 entered promiscuous mode
[  61.660000] ADDRCONF(NETDEV_UP): lan3: link is not ready
[  61.660000] device lan3 entered promiscuous mode
[  61.700000] ADDRCONF(NETDEV_UP): lan4: link is not ready
[   61.700000] device lan4entered promiscuous mode
[   61.740000]ADDRCONF(NETDEV_UP): wan: link is not ready
[   63.510000] br-eth: port1(eth0) entered forwarding state
[   63.990000] cfg80211:Calling CRDA for country: CN
[   63.990000] cfg80211:Regulatory domain changed to country: CN
[   64.000000] cfg80211:   (start_freq - end_freq @ bandwidth),(max_antenna_gain, max_eirp)
[   64.010000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz),(N/A, 2000 mBm)
[   64.010000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz),(N/A, 3000 mBm)
[   68.510000]ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   68.530000] device wlan0entered promiscuous mode
[   68.560000]ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   68.570000] br-eth: port2(wlan0) entered forwarding state
[   68.570000] br-eth: port2(wlan0) entered forwarding state
[   68.580000]ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   70.570000] br-eth: port2(wlan0) entered forwarding state
[   80.010000]ADDRCONF(NETDEV_UP): wan: link is not ready
[   89.630000] svc: failed toregister lockdv1 RPC service (errno 124).
[  96.720000] ADDRCONF(NETDEV_UP): wan: link is not ready
[  113.000000]ADDRCONF(NETDEV_UP): wan: link is not ready
[  128.490000]ADDRCONF(NETDEV_UP): wan: link is not ready
[  143.950000]ADDRCONF(NETDEV_UP): wan: link is not ready
[  159.410000]ADDRCONF(NETDEV_UP): wan: link is not ready
[  174.880000]ADDRCONF(NETDEV_UP): wan: link is not ready
[  190.350000]ADDRCONF(NETDEV_UP): wan: link is not ready
[  205.820000]ADDRCONF(NETDEV_UP): wan: link is not ready
[  221.290000]ADDRCONF(NETDEV_UP): wan: link is not ready
[  236.780000]ADDRCONF(NETDEV_UP): wan: link is not ready
[  252.250000] ADDRCONF(NETDEV_UP):wan: link is not ready
[  267.710000]ADDRCONF(NETDEV_UP): wan: link is not ready


主题

好友

334

积分

少尉

签到天数: 1 天

[LV.1]初来乍到

发表于 2017-7-13 19:22 |显示全部楼层
coolslob 发表于 2017-7-13 18:29
看这个信息,路由好像是正常启动了的。

没看到eth0 up吗?已经弄好了,救砖成功。系统都没刷。breed也刷好了。就是突然发现MAC变了,跟背面的不一致
回复

使用道具 举报

主题

好友

1158

积分

上尉

签到天数: 16 天

[LV.4]偶尔看看III

发表于 2017-7-12 12:58 |显示全部楼层
正面U-BOOT存在,直接复位进uboot刷机
回复

使用道具 举报

主题

好友

334

积分

少尉

签到天数: 1 天

[LV.1]初来乍到

发表于 2017-7-12 13:30 |显示全部楼层
bushann 发表于 2017-7-12 12:58
正面U-BOOT存在,直接复位进uboot刷机

什么意思啊???
回复

使用道具 举报

主题

好友

1656

积分

上尉

签到天数: 150 天

[LV.7]常住居民III

发表于 2017-7-12 19:16 |显示全部楼层
证明U-BOOT存在,直接复位进uboot刷机
回复

使用道具 举报

主题

好友

334

积分

少尉

签到天数: 1 天

[LV.1]初来乍到

发表于 2017-7-12 19:46 |显示全部楼层
hwh8238 发表于 2017-7-12 19:16
证明U-BOOT存在,直接复位进uboot刷机

怎么刷机???
回复

使用道具 举报

主题

好友

2169

积分

少校

签到天数: 4 天

[LV.2]偶尔看看I

发表于 2017-7-12 22:40 |显示全部楼层
TFTP也可以,SecureCRT或者PUTTY都可以
回复

使用道具 举报

主题

好友

334

积分

少尉

签到天数: 1 天

[LV.1]初来乍到

发表于 2017-7-12 23:02 |显示全部楼层
nnsat 发表于 2017-7-12 22:40
TFTP也可以,SecureCRT或者PUTTY都可以

什么
回复

使用道具 举报

主题

好友

593

积分

中尉

该用户从未签到

发表于 2017-7-13 18:28 |显示全部楼层
果然砖了,  看到你问怎么刷breed的帖子,就猜想这路由怕是要砖了
回复

使用道具 举报

主题

好友

593

积分

中尉

该用户从未签到

发表于 2017-7-13 18:29 |显示全部楼层
看这个信息,路由好像是正常启动了的。
回复

使用道具 举报

主题

好友

1262

积分

上尉

签到天数: 113 天

[LV.6]常住居民II

发表于 2017-7-16 19:59 |显示全部楼层
没看懂啊。。
回复

使用道具 举报

主题

好友

334

积分

少尉

签到天数: 1 天

[LV.1]初来乍到

发表于 2017-7-18 21:25 |显示全部楼层

反正已经好了      
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 我要加入

本版积分规则

Archiver| 手机版| 中国无线门户 ( 粤ICP备11076993 )  |网站地图

GMT+8, 2017-9-26 20:55

Powered by Discuz! X3.2

© 2003-2013 广州威思信息科技有限公司

返回顶部 返回列表